邱坤,原君静,王海宁,付宏生.高速干式铣削马氏体不锈钢的表面质量与组织特性[J].表面技术,2014,43(5):20-24,60.
QIU Kun,YUAN Jun-jing,WANG Hai-ning,FU Hong-sheng.英文标题[J].Surface Technology,2014,43(5):20-24,60
高速干式铣削马氏体不锈钢的表面质量与组织特性
英文标题
投稿时间:2014-04-15  修订日期:2014-06-02
DOI:
中文关键词:  马氏体不锈钢  高速切削  塑性变形  过度回火马氏体
英文关键词:martensite steel  high-speed cutting  plastic deformation layer  over-tempered martensite
基金项目:北京市教育委员会科技计划项目 ( sqkm201210858005)
作者单位
邱坤 北京电子科技职业学院 机械工程学院, 北京 100176 
原君静 北京电子科技职业学院 机械工程学院, 北京 100176 
王海宁 北京理工大学 机械与车辆学院, 北京 100081 
付宏生 北京电子科技职业学院 机械工程学院, 北京 100176 
AuthorInstitution
QIU Kun Department of Mechanical Engineering, Beijing Electronic Science and Technology Vocational College, Beijing 100176, China 
YUAN Jun-jing Department of Mechanical Engineering, Beijing Electronic Science and Technology Vocational College, Beijing 100176, China 
WANG Hai-ning School of Mechanical & Vehicular Engineering, Beijing Institute of Technology, Beijing 100081, China 
FU Hong-sheng Department of Mechanical Engineering, Beijing Electronic Science and Technology Vocational College, Beijing 100176, China 
摘要点击次数:
全文下载次数:
中文摘要:
      目 的 研究高速干切削 工艺 对难加工材料加工表面质量的 影响规律。 方法 在切削 速度范围157 ~ 314 m /min 内 , 依据析因 试验设计方法, 对马氏体不锈钢工件进行干切削 条件下的端面铣削 工艺 试验, 考查铣削 加工表面粗糙度变化规律、表面微结构组织特征与 维氏硬度分布曲线。 结果 由每齿进给量和铣削 深度共同 决定的切屑截面构形对马氏体不锈钢加工表面轮廓的形成机制有显著作用 , 加工表面的表层及次表层组织主要由塑性变形层与 回火多 相组织层共同 构成。 结论 为 减小干式切削 对加工表面层组织特征的影响, 应优先选择大进给量、小切深的工艺参数组合。
英文摘要:
      Objective To investigate the influences of high-speed dry cutting process on the surface quality of difficult-to-cut materials. Methods Face milling experiment of martensite stainless steel was conducted at the cutting regime of 157 ~ 314 m/min in dry cutting condition under the guidance of 2K factorial design method, the characteristics of surface roughness, microstructure properties and micro-hardness distribution curves were studied experimentally. Results It was shown that: the chip cross section determined by the depth of cut and feed per tooth had significant influence on the formation of roughness profiles; severe plastic deformation and multi-phases structures were the main components of the surface and subsurface layers. Conclusion In order to reduce the negative effects of dry cutting process on machined surfaces, the cutting parameters should be carefully controlled, larger feed per tooth and smaller depth of cut are preferred.
查看全文  查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第24165559位访问者    渝ICP备15012534号-3

版权所有:《表面技术》编辑部 2014 surface-techj.com, All Rights Reserved

邮编:400039 电话:023-68792193传真:023-68792396 Email: bmjs@surface-techj.com

渝公网安备 50010702501715号