王星星,龙伟民,裴夤崟,沈元勋,吕登峰,佘春.BAg45 CuZn 钎料表面化学镀锡的研究[J].表面技术,2013,42(3):56-58,107. WANG Xing-xing,LONG Wei-min,PEI Yin-yin,SHEN Yuan-xun,LYU Deng-feng,SHE Chun.Research of Electroless Tin Plating on BAg45 CuZn Brazing Filler[J].Surface Technology,2013,42(3):56-58,107 |
BAg45 CuZn 钎料表面化学镀锡的研究 |
Research of Electroless Tin Plating on BAg45 CuZn Brazing Filler |
投稿时间:2013-01-08 修订日期:2013-01-23 |
DOI: |
中文关键词: 钎料 化学镀锡 沉积速率 锡含量 润湿性 |
英文关键词:brazing filler electroless tin plating depositing rate tin content wettability |
基金项目:国家重点基础研究发展计划项目(2012CB723902) ;国家高技术研究发展计划项目(2012AA040208) |
|
Author | Institution |
WANG Xing-xing | State Key Laboratory of Advanced Brazing Filler Metals and Technology,Zhengzhou Research Institute of Mechanical Engineering, Zhengzhou 450001 , China |
LONG Wei-min | State Key Laboratory of Advanced Brazing Filler Metals and Technology,Zhengzhou Research Institute of Mechanical Engineering, Zhengzhou 450001 , China |
PEI Yin-yin | State Key Laboratory of Advanced Brazing Filler Metals and Technology,Zhengzhou Research Institute of Mechanical Engineering, Zhengzhou 450001 , China |
SHEN Yuan-xun | State Key Laboratory of Advanced Brazing Filler Metals and Technology,Zhengzhou Research Institute of Mechanical Engineering, Zhengzhou 450001 , China |
LYU Deng-feng | State Key Laboratory of Advanced Brazing Filler Metals and Technology,Zhengzhou Research Institute of Mechanical Engineering, Zhengzhou 450001 , China |
SHE Chun | State Key Laboratory of Advanced Brazing Filler Metals and Technology,Zhengzhou Research Institute of Mechanical Engineering, Zhengzhou 450001 , China |
|
摘要点击次数: |
全文下载次数: |
中文摘要: |
在 BAg45 CuZn 钎料表面进行化学镀锡,分析镀液温度、pH 值、施镀时间对锡镀层的沉积速率和AgCuZnSn 钎料中锡含量的影响规律,确定最佳工艺,并表征锡镀层的表面形貌和 AgCuZnSn 钎料的润湿性。 分析表明:随着温度和 pH 值升高,镀层沉积速率和 AgCuZnSn 钎料锡含量均先升高,后降低;随着施镀时间的延长,沉积速率先增大,后快速减小,而 AgCuZnSn 钎料 Sn 含量逐渐增大。 采用最佳工艺时,沉积速率达到 13 . 6 μm / h,锡镀层的表面平整、致密度高,所得钎料的 Sn 含量为 2 . 45% ,与基体 BAg45 CuZn 钎料相比,其润湿性有大幅度提高,铺展性好。 |
英文摘要: |
The experiment of electroless tin plating on BAg45 CuZn brazing filler was investigated. The effect of plating bath temperature, pH value, plating time on depositing rate and tin content of AgCuZnSn brazing filler were analyzed. The optimal plating conditions were obtained. The surface morphology of tin coating and the wettability of AgCuZnSn brazing filler were characterized. The results indicate that the deposition rate and tin content of AgCuZnSn brazing filler initially increase and then decrease with the increase of bath temperature and pH value. With increasing of the plating time, the plating rate of tin coating also increase firstly and then decrease sharply, but the tin content of AgCuZnSn brazing filler increase gradually. Under the optimized conditions, the tin coating on BAg45CuZn brazing filler is composed of smooth and uniform,then the depositing rate of tin coating is as much as 13. 6 μm / h, tin content of 2. 45% in AgCuZnSn brazing filler. The wettability of the AgCuZnSn brazing filler has greatly improved than the BAg45CuZn brazing filler matrix under the optimal conditions, it possess good spreadability. |
查看全文 查看/发表评论 下载PDF阅读器 |
关闭 |
|
|
|